Metrologic Instruments MS1890 Manuale Utente

METROLOGIC INSTRUMENTS, INC. MS1890 Series Area Imaging Bar Code Scanner Installation and User’s Guide

6 INTRODUCTION Labels Each scanner has a label located on the underside of the head. This label provides the unit’s model number, date of manufac

7INSTALLING THE SCANNER TO THE HOST SYSTEM RS232 MS1890-14 1. Turn off the host device. 2. Plug the male 10-pin RJ45 end of the PowerLink cabl

8 INSTALLING THE SCANNER TO THE HOST SYSTEM Keyboard Wedge MS1890-47 1. Turn off the host device. 2. Plug the 10-pin RJ45 male end of the Power

9INSTALLING THE SCANNER TO THE HOST SYSTEM Stand Alone Keyboard MS1890-47 1. Turn off the host device. 2. Plug the male 10-pin RJ45 end of the

10 INSTALLING THE SCANNER TO THE HOST SYSTEM IBM MS1890-11 1. Turn off the host device. 2. Plug the male 10-pin RJ45 end of the MVC cable into

11INSTALLING THE SCANNER TO THE HOST SYSTEM Integrated USB: Full Speed MS1890-40 Low Speed MS1890-38 1. Turn off the host device. 2. Plug the

12 SCANNER OPERATION Multi-Try Trigger Mode* 1. The IR detects an object in the IR activation range and automatically turns on linear illuminati

13SCANNER OPERATION Audible Indicators When the MS1890 is in operation, it provides audible feedback. These sounds indicate the status of the sc

14 SCANNER OPERATION Visual Indicators The MS1890 has three LED indicators (yellow, white and blue) located on the top of the scanner. When the

15SCANNER OPERATION Failure Modes Long Razzberry Tone – During Power Up Failed to initialize or configure the scanner. If the scanner does not re

Copyright © 2007 by Metrologic Instruments, Inc. All rights reserved. No part of this work may be reproduced, transmitted,

16 SCANNER OPERATION Depth of Field by Minimum Bar Code Element Width MINIMUM BAR CODE ELEMENT WIDTH 1D PDF A B C D E F G mm .132 .19 .254 .3

17SCANNER OPERATION IR Activation Range The MS1890 has a built in object detection sensor that instantly turns on the scanner when an object is p

18 TROUBLESHOOTING GUIDE The following guide is for reference purposes only. Contact a Metrologic representative at 1-800-ID-Metro or 1-800-436-38

19TROUBLESHOOTING GUIDE Symptoms Possible Causes Solution The unit powers up, but does not beep when bar code is scanned. The beeper is disabled

20 TROUBLESHOOTING GUIDE Symptoms Possible Causes Solution The print quality of the bar code is suspect. Check print mode. The type of printer c

21TROUBLESHOOTING GUIDE Symptoms Possible Causes Solution The unit is transmitting each character twice. The configuration is not set correctly.

22 DESIGN SPECIFICATIONS MS1890 DESIGN SPECIFICATIONS OPERATIONAL Light Source: LED 645 nm Pulse Duration: 1 ms to 8 ms Maximum Output of

23DESIGN SPECIFICATIONS MS1890 DESIGN SPECIFICATIONS ELECTRICAL Input Voltage: 5.0VDC ± 0.25V Peak = 2 W (Typical) Operating = 1.65 W (Typ

24 APPLICATIONS AND PROTOCOLS The model number on each scanner includes the scanner number and factory default communications protocol. SCANNER VE

25DEFAULT SETTINGS – COMMUNICATION PARAMETERS Many functions of the scanner can be configured or enabled/disabled. The scanner is shipped from th

iiTABLE OF CONTENTS Introduction Product Overview ... 1 S

26 DEFAULT SETTINGS – COMMUNICATION PARAMETERS PARAMETER DEFAULT RS232 IBM 46XX KBW USB MSI-Plessy 10/10 Check Digit 9 9 9 9 MSI-Plessy M

27DEFAULT SETTINGS – COMMUNICATION PARAMETERS PARAMETER DEFAULT RS232 IBM 46XX KBW USB Transmit UPC-A Item ID# * 9 9 9 9 Transmit Codabar

28 DEFAULT SETTINGS – COMMUNICATION PARAMETERS PARAMETER DEFAULT RS232 IBM 46XX KBW USB XON/XOFF Handshaking 9 ACK/NAK 9 Two Digit Su

29CONFIGURATION MODES The MS1890 Series has three modes of configuration. • Bar Codes The MS1890 can be configured by scanning the bar codes inc

30 UPGRADING THE FLASH ROM FIRMWARE The MetroSet2 program is a functional component of Metrologic’s new line of Flash- based scanners. This progr

31SCANNER AND CABLE TERMINATIONS Scanner Pinout Connections MS1890-14, RS232 Pin Function 1 Ground 2 RS232 Transmit Output 3 RS232 Receive Input

32 SCANNER AND CABLE TERMINATIONS Scanner Pinout Connections MS1890-38, Low Speed USB Pin Function 1 Ground 2 RS232 Transmit Output 3 RS232 Rece

33SCANNER AND CABLE TERMINATIONS Cable Connector Configurations (Host End) RS232 PowerLink Cable MLPN 53-53700x-3 Pin Function 1 Shield Ground

34 SCANNER AND CABLE TERMINATIONS Cable Connector Configurations (Host End) Keyboard Wedge PowerLink Cable MLPN 53-53702x-3 Pin Function 1 Keybo

35LIMITED WARRANTY The MS1890 series scanners are manufactured by Metrologic at its Blackwood, New Jersey, U.S.A. facility. The MS1890 series scan

iiiTABLE OF CONTENTS Scanner and Cable Terminations Scanner Pinout Connections...

36 REGULATORY COMPLIANCE Safety ITE Equipment IEC 60950-1, EN 60950-1 LED Class 1 LED Product: IEC 60825-1:1993+A1+A2, EN 60825-1:1994+A1+A2

37REGULATORY COMPLIANCE EMC Emissions FCC Part 15, ICES-003, CISPR 22, EN 55022 Immunity CISPR 24, EN 55024 Changes or modifications not expres

38 REGULATORY COMPLIANCE EMC Changes or modifications not expressly approved by the party responsible for compliance could void the user’s author

39PATENTS This METROLOGIC product may be covered by, but not limited to, one or more of the following U.S. Patents: U.S. Patent No.; 7,086,595;

40 INDEX A AC ...2, 7–11, 23 Accessories ...2 Adapter...

41INDEX Light Levels ...23 Light Source ...22 M Maintenance...

42

June 2007 Printed in the USA 00-02293A

1INTRODUCTION Product Overview The MS1890 is a rugged, high performance hand-held area imaging bar code scanner that utilizes a high-resolutio

2 INTRODUCTION Scanner and Accessories BASIC KIT Part # Description MS1890 Area Imaging Bar Code Scanner 00-02544 MetroSelect® Single-Line

3INTRODUCTION Scanner and Accessories OPTIONAL ACCESSORIES Part # Description 53-53713x-N-3 USB Full Speed Cable Locking Plus-Power™ Type A, 2.7

4 INTRODUCTION Scanner Components No. Item Description 1 Blue LED See Visual Indicators (on page 14) 2 White LED See Visual Indicators (on page

5INTRODUCTION The PowerLink Cable Connecting Important: If the PowerLink cable is not fully latched, the unit can power intermittently. Figure